C&S Connect
 
ASME Proposals Available For Public Review

Public comments may be submitted on proposed new ASME Standards drafts and on proposals to revise, reaffirm, or withdraw approval of existing ASME Standards. Comments should be addressed to the Staff Contact indicated for the particular proposal, with a copy to the Board of Standards Review, American National Standards Institute, 25 West 43rd Street, New York, NY 10036. Fax: 212-840-2298; e-mail: psa@ansi.org

All ASME public review proposals are available in hard copy at no cost and may be ordered from:

Terrell Henry, Administrator
E-mail: ansibox@asme.org
ASME Codes & Standards
Two Park Avenue
New York, NY 10016

Some proposals are also available electronically, directly from this page for no cost. Proposals that are available electronically are those which contain a link entitled "Public Review Draft File" at the end of the announcement. Simply click on that link to access the public review proposal.

For proposed reaffirmations and withdrawals, copies of the current standard may be purchased from ASME Customer Care at customercare@asme.org or by calling 800-843-2763. You may also purchase a copy online at https://www.asme.org/shop/standards.

Sort the Search Results by clicking on an underlined column header.
Title: Single Copy Price: Staff Contact: Comment Period End Date:

Revise current ANS: ASME A13.1 - 20XX, Scheme for the Identification of Piping Systems

$0

Riad Mohamed 08/11/20
This Standard is intended to establish a common system to assist in identification of hazardous materials conveyed in piping systems and their hazards when released in the environment.

Public Review Draft File(2922KB)

Revise current ANS: ASME STS-1 - 20XX, Steel Stacks

$0

Justin Cassamassino 08/16/20
The Standard applies to steel stacks; i.e., those stacks where the primary supporting shell is made of steel. It outlines the consideration that must be made for both the mechanical and structural design, such as what consideration must be taken for wind- and seismic-induced vibrations. The document provides guidelines for the selection of material, linings, and coatings, and gives the requirements for lighting and lightning protection based upon existing building and federal codes. Additionally, this Standard gives the requirements for climbing and access based upon current Occupational Safety and Health Administration (OSHA) standards, emphasizes the important areas regarding fabrication and construction, and outlines areas requiring maintenance and inspection following initial operation. Although many of the topics within these guidelines may be used for all stacks, this Standard is intended to provide design guidelines for stacks containing nonflammable gases, such as combustion exhaust gases at low internal pressures.

Public Review Draft File(759KB)

Revise current ANS: ASME B16.34 - 20XX, Valves — Flanged, Threaded, and Welding End

$0

Andres Carrion 08/17/20
This Standard applies to new construction and covers pressure–temperature ratings, dimensions, tolerances, materials, nondestructive examination requirements, testing, and marking for cast, forged, and fabricated flanged, threaded, and welding end and wafer or flangeless valves of steel, nickel-base alloys, and other alloys.

Public Review Draft File(5369KB)

Reaffirm current ANS: ASME Y14.43-2011 - R20XX, Dimensioning and Tolerancing Principles for Gages and Fixtures

$110

Fred Constantino 08/18/20
This Standard presents the design practices for dimensioning and tolerancing of gages and fixtures used for the verification of maximum material condition (MMC) size envelopes and virtual condition boundaries generated by geometric tolerances controlled at MMC, and datum features controlled at maximum material boundary (MMB).

For proposed reaffirmations and withdrawals, copies of the current standard may be purchased from ASME Customer Care at customercare@asme.org or by calling 800-843-2763. You may also purchase a copy online at https://www.asme.org/shop/standards.

Withdraw current ANS: ASME B32.100-2016 - 20XX, Preferred Metric Sizes for Flat, Round, Square, Rectangular, and Hexagonal Metal Products

$35

Daniel Papert 08/18/20
This Standard established a preferred series of metric thicknesses, widths, and lengths for flat metal products of rectangular cross-section. The thicknesses and widths shown in this Standard are also applicable to base metals that may be coated in later operations. This Standard also establishes a preferred series of metric sizes for round, square, rectangular, and hexagonal metal products.

Public Review Draft File(718KB) For proposed reaffirmations and withdrawals, copies of the current standard may be purchased from ASME Customer Care at customercare@asme.org or by calling 800-843-2763. You may also purchase a copy online at https://www.asme.org/shop/standards.

Revise current ANS: ASME B31.9 - 20XX, Building Services Piping

$0

Ray Rahaman 08/18/20
This Code Section has rules for the piping in industrial, institutional, commercial, and public buildings, and multi-unit residences, which does not require the range of sizes, pressures, and temperatures covered in B31.1. This Code prescribes requirements for the design, materials, fabrication, installation, inspection, examination, and testing of piping systems for building services.

Public Review Draft File(9867KB)

Reaffirm current ANS: ASME PTC 12.1 - 2015 - R20XX, Closed Feedwater Heaters

$160

Angel L. Guzman Rodriguez 08/25/20
This Code provides procedures, direction, and guidance for determining the thermohydraulic performance of a closed feedwater heater. It can be utilized to verify contractual performance for a new heater or to calculate performance of an existing heater in comparison to the design point.

For proposed reaffirmations and withdrawals, copies of the current standard may be purchased from ASME Customer Care at customercare@asme.org or by calling 800-843-2763. You may also purchase a copy online at https://www.asme.org/shop/standards.

Create a new American National Standard (ANS): ASME B89.4.23 - 20XX, X -RAY COMPUTED TOMOGRAPHY (CT) PERFORMANCE EVALUATION STANDARD

$0

Justin Cassamassino 08/25/20
This Standard specifies the dimensional measurement accuracy of industrial X-ray computed tomography (CT) systems for length, size, and form measurands of sphere-based test objects made of homogeneous materials. Medical CT systems are outside the scope of this Standard. This Standard is applicable to dimensional measurements made at the surface of the workpiece, i.e., at the workpiece material–air interface, including those of internal cavities.

Public Review Draft File(880KB)

Revise current ANS: ASME B16.47 - 20XX, Large Diameter Steel Flanges NPS 26 Through NPS 60 Metric/ Inch Standard

$0

Andres Carrion 08/25/20
This Standard covers pressure–temperature ratings, materials, dimensions, tolerances, marking, and testing for pipe flanges in sizes NPS 26 through NPS 60. Included are flanges with rating class designations 75, 150, 300, 400, 600, and 900 with requirements given in both SI (Metric) and U.S. Customary units, with diameter of bolts and flange bolt holes expressed in inch units.

Public Review Draft File(5368KB)

Revise current ANS: ASME NM.1 - 20XX, Thermoplastic Piping Systems

$0

Jihoon Oh 08/31/20
(a) This standard prescribes requirements for the design, materials, fabrication, erection, examination, testing, and inspection of thermoplastic piping systems.

(b) Thermoplastic piping as used in this standard includes pipe, flanges, bolting, gaskets, valves, fittings, special connecting components, and the pressure containing portions of other piping components, whether manufactured in accordance with Standards referenced in this standard or specially designed. It also includes hangers and supports and other equipment items necessary to prevent overstressing the pressure containing components.

Public Review Draft File(12474KB)

Next 10

Minimum Site Requirements: IE 6.0+Firefox 2.0+Chrome 4.0+

Copyright © 1996-2016 ASME. All Rights Reserved. Terms of Use | Privacy Statement